Ionization Techniques Research Articles

Improved Detection of Tryptic Peptides from Tissue Sections Using Desorption Electrospray Ionization Mass Spectrometry Imaging.

DESI-MSI is an ambient ionization technique used frequently for the detection of lipids, small molecules, and drug targets. Until recently, DESI had only limited use for the detection of proteins and peptides due to the setup and needs around deconvolution of data resulting in a small number of species being detected at lower spatial resolution. There are known differences in the ion species detected using DESI and MALDI for nonpeptide molecules, and here, we identify that this extends to proteomic species. DESI MS images were obtained for tissue sections of mouse and rat brain using a precommercial heated inlet (approximately 450 °C) to the mass spectrometer. Ion mobility separation resolved spectral overlap of peptide ions and significantly improved the detection of multiply charged species. The images acquired were of pixel size 100 μm (rat brain) and 50 μm (mouse brain), respectively. Observed tryptic peptides were filtered against proteomic target lists, generated by LC-MS, enabling tentative protein assignment for each peptide ion image. Precise localizations of peptide ions identified by DESI and MALDI were found to be comparable. Some spatially localized peptides ions were observed in DESI that were not found in the MALDI replicates, typically, multiply charged species with a low mass to charge ratio. This method demonstrates the potential of DESI-MSI to detect large numbers of tryptic peptides from tissue sections with enhanced spatial resolution when compared to previous DESI-MSI studies.

Pressure-Driven Switching of Photoelectron Impact Ionization-Chemical Ionization/Penning Ionization in Vacuum Ultraviolet Photoionization Mass Spectrometry.

Vacuum ultraviolet photoionization (VUV-PI) is a soft ionization technique that operates under pressures ranging from vacuum to ambient pressure. VUV-PI has played an essential role in direct sampling mass spectrometry. In this study, new ionization processes initiated by photoelectrons have been studied through the inclusion of a radio frequency (RF) electric field at different pressures. After deducting the contribution of single photoionization (SPI), the signal intensity of 1 ppmv toluene (C7H8+) in Ar was approximately 5-fold higher than that in N2. Mixed gases with different ionization energies (IEs) and excitation energies (EEs) were further investigated to reveal that metastable species were involved in the enhancement process. Reactant ions were produced by photoelectron impact ionization (PEI), which further triggered ion-molecule reactions, i.e., chemical ionization (CI). Metastable species were produced by photoelectron impact excitation (PEE), which further triggered Penning ionization (PenI). Analytes with IEs above 10.6 eV, such as CO2 (IE = 13.78 eV) and CHCl3 (IE = 11.37 eV), could be sensitively ionized by PenI with a sensitivity comparable to SPI. Except for the contribution of SPI, the dominant ionization process was switched from PEI-CI to PenI when the pressure was elevated from 50 to 500 Pa, as the electron energy gradually decreased and was only able to produce metastable states based on the kinetic energy balance equation of electrons. The conversion processes and conditions from PEI-CI to PenI will provide novel insights to develop new selective and sensitive VUV-PI sources and understand the ionization mechanism in other discharge ionization sources.

Matrix- and Surface-Assisted Laser Desorption/Ionization Mass Spectrometry Methods for Urological Cancer Biomarker Discovery-Metabolomics and Lipidomics Approaches.

Urinary tract cancers, including those of the bladder, the kidneys, and the prostate, represent over 12% of all cancers, with significant global incidence and mortality rates. The continuous challenge that these cancers present necessitates the development of innovative diagnostic and prognostic methods, such as identifying specific biomarkers indicative of cancer. Biomarkers, which can be genes, proteins, metabolites, or lipids, are vital for various clinical purposes including early detection and prognosis. Mass spectrometry (MS), particularly soft ionization techniques such as electrospray ionization (ESI) and laser desorption/ionization (LDI), has emerged as a key tool in metabolic profiling for biomarker discovery, due to its high resolution, sensitivity, and ability to analyze complex biological samples. Among the LDI techniques, matrix-assisted laser desorption/ionization (MALDI) and surface-assisted laser desorption/ionization (SALDI) should be mentioned. While MALDI methodology, which uses organic compounds as matrices, is effective for larger molecules, SALDI, based on the various types of nanoparticles and nanostructures, is preferred for smaller metabolites and lipids due to its reduced spectral interference. This study highlights the application of LDI techniques, along with mass spectrometry imaging (MSI), in identifying potential metabolic and lipid biomarkers for urological cancers, focusing on the most common bladder, kidney, and prostate cancers.

Mass spectrometry of dendrimers.

Mass spectrometry (MS) has become an essential technique to characterize dendrimers as it proved efficient at tackling analytical challenges raised by their peculiar onion-like structure. Owing to their chemical diversity, this review covers benefits of MS methods as a function of dendrimer classes, discussing advantages and limitations of ionization techniques, tandem mass spectrometry (MS/MS) strategies to determine the structure of defective species, as well as most recently demonstrated capabilities of ion mobility spectrometry (IMS) in the field. Complementarily, the well-defined structure of these macromolecules offers major advantages in the development of MS-based method, as reported in a second section reviewing uses of dendrimers as MS and IMS calibration standards and as multifunctional charge inversion reagents in gas phase ion/ion reactions.

N-H and N-C Bond Dissociation Pathways in Ultraviolet Photodissociation of Dimethylamine.

We investigated the interlinked N-H and N-C photochemistry of primary and secondary amines via the state-resolved detection of vibrationally excited CH3 product and H atom product by 200-235 nm dimethylamine photodissociation using resonance-enhanced multiphoton ionization (REMPI) and velocity map imaging (VMI) techniques. The out-of-plane bending (ν2) vibrationally excited CH3 showed a bimodal translational energy distribution that became unimodal with a near-zero product yield at longer photolysis wavelengths (λphotolysis). In contrast, a unimodal distribution was observed for the C-H stretching (νCH) vibrationally excited CH3 products with an almost constant product yield in the examined λphotolysis region. We ascribed the state-specific energy releases of the CH3 products to two reaction pathways based on calculations of the potential energy surface (PES): the direct N-CH3 dissociation pathway and the indirect N-CH3 dissociation pathway via the N-H bond conical intersection. Meanwhile, the H atom product showed a bimodal energy distribution similar to the ammonia photodissociation model, with an excited-state counterproduct channel that became accessible at a shorter λphotolysis. These results suggest that the N-H and N-C bond dissociations are connected, and these dissociations cause different photochemistry between primary/secondary amines and tertiary amines.

Observation of Large, Charged Droplet Signatures within the High-Vacuum Region of a Commercial Electrospray TOF-MS.

Electrospray ionization (ESI) is one of the most prominent atmospheric pressure ionization techniques in modern mass spectrometry. It generates charged droplets from an analyte-containing solution as an initial step in the ionization process. Textbooks and the majority of the articles assume the entire droplet evaporation and release of bare analyte ions within the ionization chamber. However, non-mass-spectrometry-related literature and recent reports demonstrate droplet observation in regions of the vacuum systems of a variety of mass spectrometers. In this work, we report on the observation of large droplet fragments within the orthogonal acceleration stage of a Bruker micrOTOF by connecting an oscilloscope to an auxiliary ion current detector downstream of the acceleration stage. Moreover, we detected fragment debris even with the MCP TOF detector by evaluating individual TOF spectra. Droplet fragments appear as pronounced and intensive pulses of the ion current. This observation is clearly connected to ESI, as other atmospheric pressure ionization methods do not show this behavior. The recorded droplet signatures show clear dependencies on the ion source and transfer stage parameters. The existence of large and highly charged droplets may adversely affect or at least impact the analytical performance of the instrument due to space charge or complex heterogeneous chemical reactions. Furthermore, the penetration of large charged aggregates into the vacuum system explains the reported surface contamination after multipole stages. This contamination of critical components leads to substantially higher maintenance efforts.

Identification of Phytochemicals in Cleome rutidosperma DC. Methanol Extract and Evaluate its Efficacy on Some Common Rice Field Weeds

Screening different plant species for herbicidal activity and identifying new allelochemicals with novel structures and phytochemical activity could be promising candidates for reducing the negative consequences of chemical herbicides. Our study aims to investigate the allelopathic substance(s) and herbicidal efficacy of Cleome rutidosperma DC. on rice filed weeds in the lab and glasshouse. The phytochemical constituents of the methanol extract of Cleome rutidosperma were analyzed by high-performance liquid chromatography coupled with electrospray ionization quadrupole time-of-flight mass spectrometry (HPLC-ESI-QTOF-MS). The allelopathic effect of C. rutidosperma has been further studied on the germination and early development of five common rice field weeds: Echinochloa crus-galli (L.) P. Beauv., Fimbristylis miliacea (L.) Vahl, Oryza sativa f. spontanea Roshev., Leptochloa chinensis (L.) Nees, and Cyperus iria L. The seed germination and growth of tested weeds under lab and glasshouse conditions were compared to three concentrations of C. rutidosperma methanol extract at 2.5, 5, and 10% with the control (only distilled water). The results indicated the presence of 64 and 10 known chemicals using positive and negative ionization techniques, the majority of which were toxic. The inhibitory effect of C. rutidosperma was stronger in the lab than in the glasshouse. No seed germination of the tested species was observed when 10% C. rutidosperma extract was applied. The photosynthesis rate of C. iria exhibited a higher reduction (70.56%) compared to other species at higher doses (10%) of C. rutidosperma. These findings demonstrated that C. rutidosperma is a significant source of phytotoxic components and can be used to develop future bio-herbicides. The outcome of this study can be employed in the organic management of weeds and reduce our heavy reliance on synthetic herbicides.

Superradiance of ultracold cesium Rydberg $|65D_{5/2}\rangle $ $\to$ $|66P_{3/2}\rangle$

Abstract We investigate Rydberg $|65D_{5/2}\rangle $ $\to$ $|66P_{3/2}\rangle$ superradiance in a dense ultracold cesium atoms, where the ground atoms are excited to $|65D_{5/2}\rangle$ Rydberg states via two-photon excitation in a standard magneto-optical trap. The superradiant spectrum of $|65D_{5/2}\rangle$ $\to$ $|66P_{3/2}\rangle$ is obtained using the state selective field ionization technique. We observe its dynamic evolution process by varying the delay time of ionization field $t_{d}$. The results show that the evolution process of $|65D_{5/2}\rangle $ $\to$ $|66P_{3/2}\rangle$ is much shorter than its radiation lifetime at room temperature, which verify the superradiance effect. The dependence of superradiance process on Rydberg atoms number $N_{e}$ and principal quantum number $n$ are investigated. The results shows the superradiance become fast with increasing $N_{e}$, while it is suppressed for stronger van der Waals (vdW) interaction. Superradiance has a potential application in quantum technologies, and the Rydberg atom is an ideal medium for superradiance. Our system is good for studying the strong two-body interaction between Rydberg atoms.

Perspective on SPME-MS: Green and high-performance methods for rapid screening

The direct coupling of solid-phase microextraction (SPME) with mass spectrometry (MS) offers rapid analysis with high sensitivity and low matrix effects by benefiting from the integration of sampling, high enrichment, and clean-up functions of SPME. Eliminating chromatographic separation reduces the amount of gas/solvent needed for analysis, while direct desorption in SPME-MS consumes none or few microliters of organic solvents per sample, further enhancing the greenness of the SPME technology. Over the past two decades, the rapid evolution of SPME-MS has given rise to numerous novel technologies that employ diverse ionization techniques and interfaces, several of which have already been commercialized. Drawing from an extensive review published earlier this year and our research experience, we provide perspectives on three aspects of these technologies: interface design and automation, integration with state-of-art MS instrumentation, and anticipated future developments.

Moderate Signal Enhancement in Electrospray Ionization Mass Spectrometry by Focusing Electrospray Plume with a Dielectric Layer around the Mass Spectrometer's Orifice.

Electrospray ionization (ESI) is among the commonly used atmospheric pressure ionization techniques in mass spectrometry (MS). One of the drawbacks of ESI is the formation of divergent plumes composed of polydisperse microdroplets, which lead to low transmission efficiency. Here, we propose a new method to potentially improve the transmission efficiency of ESI, which does not require additional electrical components and complex interface modification. A dielectric plate-made of ceramic-was used in place of a regular metallic sampling cone. Due to the charge accumulation on the dielectric surface, the dielectric layer around the MS orifice distorts the electric field, focusing the charged electrospray cloud towards the MS inlet. The concept was first verified using charge measurement on the dielectric material surface and computational simulation; then, online experiments were carried out to demonstrate the potential of this method in MS applications. In the online experiment, signal enhancements were observed for dielectric plates with different geometries, distances of the electrospray needle axis from the MS inlet, and various compounds. For example, in the case of acetaminophen (15 μM), the signal enhancement was up to 1.82 times (plate B) using the default distance of the electrospray needle axis from the MS inlet (d = 1.5 mm) and 12.18 times (plate C) using a longer distance (d = 7 mm).

Office paper and laser printing: a versatile and affordable approach for fabricating paper-based analytical devices with multimodal detection capabilities.

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL-1, 2.7 μmol L-1, and 6.8 μmol L-1, respectively. A limit of detection of 0.048 fg mL-1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m-2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper.

Liquid electron ionization-mass spectrometry as a novel strategy for integrating normal-phase liquid chromatography with low and high-resolution mass spectrometry.

Normal-phase liquid chromatography (NPLC) plays a pivotal role in the rapid separation of non-polar compounds, facilitating isomer separation and finding applications in various crucial areas where aprotic solvents are necessary. Similar to reversed-phase liquid chromatography (RPLC), NPLC requires a robust and sensitive detector to unequivocally identify the analytes, such as a mass spectrometer. However, coupling NPLC with mass spectrometry (MS) poses challenges due to the incompatibility between the non-polar solvents used as the mobile phase and the primary ionization techniques employed in MS. Several analytical methods have been developed to combine NPLC with electrospray ionization (ESI), but these methods are restricted to the analysis of polar compounds. In most cases, atmospheric pressure chemical ionization (APCI) becomes necessary to expand the range of analysis applications. To overcome these limitations and fully realize the potential of NPLC-MS coupling, a technique termed liquid electron ionization-mass spectrometry (LEI-MS) can be used. LEI-MS offers a straightforward solution by enabling the effective coupling of NPLC with both low and high-resolution MS. LEI allows for the comprehensive analysis of non-polar compounds and provides a powerful tool for isomer separation and precise identification of analytes. Optimal separations, mass spectral qualities, and matches with the NIST library were obtained in both configurations, demonstrating the potential of the proposed approach.

Biomarker Identification in Liver Cancers Using Desorption Electrospray Ionization Mass Spectrometry (DESI-MS) Imaging: An Approach for Spatially Resolved Metabolomics.

Liver cancers are characterized by interindividual and intratumoral heterogeneity, which makes early diagnosis and the development of therapies challenging. Desorption electrospray ionization mass spectrometry (DESI-MS) imaging is a potent and sensitive MS ionization technique for direct, unaltered 2D and 3D imaging of metabolites in complex biological samples. Indeed, DESI gently desorbs and ionizes analyte molecules from the sample surface using an electrospray source of highly charged aqueous spray droplets in ambient conditions. DESI-MS imaging of biological samples allows untargeted analysis and characterization of metabolites in liver cancers to identify new biomarkers of malignancy. In this chapter, we described a detailed protocol using liver cancer samples collected and stored for histopathology examination, either as frozen or as formalin-fixed, paraffin-embedded specimens. Such hepatocellular carcinoma samples can be subjected to DESI-MS analyses, illustrating the capacity of spatially resolved metabolomics to distinguish malignant lesions from adjacent normal liver tissue.

Selective ionization of marker molecules in fuels by laser-based ion mobility spectrometry (LIMS).

Careful quality control of complex matrices such as fuels and food is necessary due to the prevalence of counterfeit and pirated goods in global trade. The addition of taggants (indicator substances) to products or their packaging helps to ensure traceability. In order to prevent the mixing of different liquid products, such as different taxed fuels, invisible labelling (marker) can be used to detect illegal activities. This study investigates the qualitative and quantitative analysis of markers in complex fuel matrices using Resonance-Enhanced Multiphoton Ionisation (REMPI) Ion Mobility Spectrometry (IMS). The potential of REMPI as a selective ionisation technique for the detection of markers is highlighted, particularly with respect to minimizing matrix background and the possibility of detection without chromatographic pre-separation. Finding a suitable marker-wavelength combination that provides a suitable marker-to-matrix ratio allows selective ionization of markers while minimising matrix background. Matrix analysis shows that higher excitation wavelengths result in reduced matrix signals, with the low intensities observed at 355 nm for diesel and petrol matrices. Several candidate markers are evaluated based on the criteria of intense signal at 355 nm and non-leachability for the low tax labelling. The analytical performance of selected markers is evaluated, with a focus on the charge transfer reaction (CTR) between markers and matrix components. Our findings demonstrate the potential of REMPI-IMS for marker analysis in fuels without the need for chromatographic pre-separation, providing a promising approach for detecting illegal or fraudulent activities in the supply chain.

Arc-Induced Electrospray Ionization Mass Spectrometry.

Arc-induced electrospray ionization mass spectrometry (AESI-MS) was developed during which alternating current electrospray is simply achieved through the arc plasma. The AESI source exploits the arc's temperature and charge properties to generate aerosols consisting of charged microdroplets. The electrospray region, in which organic molecules are contained within microdroplets, partially overlaps with the arc plasma region. Guided by the electric field, these molecules undergo ionization, yielding ionic target analytes. AESI represents a soft ionization method that combines the mechanisms of atmospheric pressure chemical ionization and electrospray ionization, facilitating the ionization of analytes with wide ranging polarities. The precisely targeted spraying area enhances ion entry into the mass analyzer, thereby enabling excellent ionization efficiency. The AESI source exhibits several notable advantages over the electrospray ionization source, including an elevated but comparable level of active species concentrations and types, simplified mass spectra for direct amino acid analysis, high salt tolerance, versatile analysis of compounds with varying polarities, and reliable quantitative analysis of amino acids in complex matrices. Overall, AESI broadens the methodologies employed to generate microdroplets, providing a technological and scientific framework for creating distinctive electrospray ionization techniques.

MSdeCIpher: A Tool to Link Data from Complementary Ionization Techniques in High-Resolution GC-MS to Identify Molecular Ions.

Electron ionization (EI) and molecular ion-generating techniques like chemical ionization (CI) are complementary ionization methods in gas chromatography (GC)-mass spectrometry (MS). However, manual curation effort and expert knowledge are required to correctly assign molecular ions to fragment spectra. MSdeCIpher is a software tool that enables the combination of two separate datasets from fragment-rich spectra, like EI-spectra, and soft ionization spectra containing molecular ion candidates. Using high-resolution GC-MS data, it identifies and assigns molecular ions based on retention time matching, user-defined adduct/neutral loss criteria, and sum formula matching. To our knowledge, no other freely available or vendor tool is currently capable of combining fragment-rich and soft ionization datasets in this manner. The tool's performance was evaluated on three test datasets. When molecular ions are present, MSdeCIpher consistently ranks the correct molecular ion for each fragment spectrum in one of the top positions, with average ranks of 1.5, 1, and 1.2 in the three datasets, respectively. MSdeCIpher effectively reduces candidate molecular ions for each fragment spectrum and thus enables the usage of compound identification tools that require molecular masses as input. It paves the way towards rapid annotations in untargeted analysis with high-resolution GC-MS.

Photophysical Outcomes of Water-Solvated Heterocycles: Single-Conformation Ultraviolet and Infrared Spectroscopy of Microsolvated 2-Phenylpyrrole.

The molecular chromophores within brown carbon (BrC) aerosols absorb solar radiation at visible and near-ultraviolet wavelengths. This contributes to the overall warming of the troposphere and the photochemical aging of aerosols. In this investigation, we combine a suite of experimental and theoretical methods to reveal the conformation-specific ultraviolet and infrared spectroscopy of 2-phenylpyrrole (2PhPy)─an extended π-conjugated pyrrole derivative and a model BrC chromophore─along with its water microsolvated molecular complexes (2PhPy:nH2O, n = 1-3). Using resonant two-photon ionization and double-resonance holeburning techniques alongside MP3 (ground state) and ADC(3) (excited state) torsional potential energy surfaces and discrete variable representation simulations, we characterized the ultraviolet spectra of 2PhPy and 2PhPy:1H2O. This analysis revealed evidence for Herzberg-Teller vibronic coupling along the CH wagging and NH stretching coordinates of the aromatic rings. Conformation-specific infrared spectroscopy revealed extended hydrogen-bonding networks of the 2PhPy:nH2O complexes. Upon stepwise addition of H2O solvation, the nearest H2O acceptor forms a strong, noncovalent interaction with the pyrrole NH donor, while the second and third H2O partners interface with the phenyl and pyrrole aromatic rings through growing van der Waals π/H atom stabilization. A local-mode Hamiltonian approach was employed for comparison with the experimental spectra, thus identifying the vibrational spectral signatures to specific 2PhPy:nH2O oscillators.

Improvement of Ionization Efficiency and Application of Structural Analysis for MALDI-TOFMS by Derivatization of Polyacrylic Acid.

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) is a suitable method for polymer analysis. MALDI is a soft ionization technique that can generate mainly singly charged ions. Therefore, the polymer's molecular weight distribution is easy to analyze, facilitating the calculation of the number average molecular weight and weight average molecular weight and polydispersity. However, there are polymers that are difficult to detect by MALDI-TOFMS. For example, polyacrylic acid includes carboxylic acid in the main chain, which is difficult to measure due to its low ionization efficiency. As a solution, the ionization efficiency was improved by methylation. In this technical report, we introduce a method to utilize derivatization to determine the degree of polymerization by accurate mass spectrometry (MS). Furthermore, the structures of both ends of the polymers were estimated by tandem time-of-flight MS.

Recent developments in ionization techniques for single-cell mass spectrometry.

The variation among individual cells plays a significant role in many biological functions. Single-cell analysis is advantageous for gaining insight into intricate biochemical mechanisms rarely accessible when studying tissues as a whole. However, measurement on a unicellular scale is still challenging due to unicellular complex composition, minute substance quantities, and considerable differences in compound concentrations. Mass spectrometry has recently gained extensive attention in unicellular analytical fields due to its exceptional sensitivity, throughput, and compound identification abilities. At present, single-cell mass spectrometry primarily concentrates on the enhancement of ionization methods. The principal ionization approaches encompass nanoelectrospray ionization (nano-ESI), laser desorption ionization (LDI), secondary ion mass spectrometry (SIMS), and inductively coupled plasma (ICP). This article summarizes the most recent advancements in ionization techniques and explores their potential directions within the field of single-cell mass spectrometry.

Recent Advances in the Detection of Food Toxins Using Mass Spectrometry.

Edibles are the only source of nutrients and energy for humans. However, ingredients of edibles have undergone many physicochemical changes during preparation and storage. Aging, hydrolysis, oxidation, and rancidity are some of the major changes that not only change the native flavor, texture, and taste of food but also destroy the nutritive value and jeopardize public health. The major reasons for the production of harmful metabolites, chemicals, and toxins are poor processing, inappropriate storage, and microbial spoilage, which are lethal to consumers. In addition, the emergence of new pollutants has intensified the need for advanced and rapid food analysis techniques to detect such toxins. The issue with the detection of toxins in food samples is the nonvolatile nature and absence of detectable chromophores; hence, normal conventional techniques need additional derivatization. Mass spectrometry (MS) offers high sensitivity, selectivity, and capability to handle complex mixtures, making it an ideal analytical technique for the identification and quantification of food toxins. Recent technological advancements, such as high-resolution MS and tandem mass spectrometry (MS/MS), have significantly improved sensitivity, enabling the detection of food toxins at ultralow levels. Moreover, the emergence of ambient ionization techniques has facilitated rapid in situ analysis of samples with lower time and resources. Despite numerous advantages, the widespread adoption of MS in routine food safety monitoring faces certain challenges such as instrument cost, complexity, data analysis, and standardization of methods. Nevertheless, the continuous advancements in MS-technology and its integration with complementary techniques hold promising prospects for revolutionizing food safety monitoring. This review discusses the application of MS in detecting various food toxins including mycotoxins, marine biotoxins, and plant-derived toxins. It also explores the implementation of untargeted approaches, such as metabolomics and proteomics, for the discovery of novel and emerging food toxins, enhancing our understanding of potential hazards in the food supply chain.